(1) Glue compounding on the composite board: check whether the panel and bottom plate of the composite board production line are dry, and pick out the board with moisture. (1) Lem majemuk pada papan komposit: periksa apakah panel dan pelat bawah dari jalur produksi papan komposit kering, dan pilih papan dengan kelembaban. Adjust the glue, adjust the glue and calcium carbonate evenly, and adjust the toner to the same color as the panel. Sesuaikan lem, sesuaikan lem dan kalsium karbonat secara merata, dan sesuaikan toner dengan warna yang sama dengan panel. According to the climate and humidity at the time, add an appropriate amount of curing agent, the ratio of curing agent to glue is 1 ~ 3%. Menurut iklim dan kelembaban pada saat itu, tambahkan jumlah bahan pengawet yang tepat, rasio bahan pengawet terhadap lem adalah 1 ~ 3%.
(2) Pre-composite process of panel: if faced with a polished surface and a mesh panel, it must be carefully selected and sent to a hand-held grinder for de-glazing. (2) Proses pra-komposit panel: jika dihadapkan dengan permukaan yang dipoles dan panel jala, itu harus dipilih dengan hati-hati dan dikirim ke gerinda genggam untuk de-glazur. It is de-aired according to the flatness, dry-grinded and leveled, but not deep-grinded; Itu ditayangkan sesuai dengan kerataan, kering digiling dan diratakan, tetapi tidak digiling dalam; then the net is broken off Cloth shovel flat surface glue. kemudian bersih dari lem kain sekop permukaan datar. If the shovel cannot be removed, you should use a hand-held grinder to grind off the net surface glue. Jika sekop tidak dapat dilepas, Anda harus menggunakan penggiling genggam untuk menggiling lem permukaan bersih. Use double-sided smoothing to remove dust from the dry-milled panel. Gunakan penghalusan dua sisi untuk menghilangkan debu dari panel giling kering.
(3) The pre-composite process of the bottom plate: the bottom plate with light should be de-glazed and then thickened, usually the thickness of 20mm bottom plate should be 17mm. (3) Proses pra-komposit pelat bawah: pelat bawah dengan cahaya harus de-kaca dan kemudian dikentalkan, biasanya ketebalan pelat bawah 20mm harus 17mm. After the bottom plate is fixed, remove moisture. Setelah pelat bawah diperbaiki, hilangkan uap air. Can be pulled outside to dry, dry or blow dry. Dapat ditarik keluar agar kering, kering atau kering. Note that if the board is not dry, it cannot be glued to avoid delamination or infirmity. Perhatikan bahwa jika papan tidak kering, papan tidak dapat dilem untuk menghindari delaminasi atau kelemahan.
(4) Select panel: select the marble panel that meets the customer's requirements. (4) Panel pilih: pilih panel marmer yang memenuhi persyaratan pelanggan. Clarify the types of materials and the consistency of colors. Memperjelas jenis bahan dan konsistensi warna. Note that when selecting the panel, it should be free of scars, warpage, trachoma, depressions, stains, etc. If the wool board does not show the effect, the panel can only be determined after spraying the board with a water gun. Perhatikan bahwa ketika memilih panel, panel harus bebas dari bekas luka, lungsin, trachoma, depresi, noda, dll. Jika papan wol tidak menunjukkan efek, panel hanya dapat ditentukan setelah menyemprot papan dengan pistol air.
Kontak Person: Mr. Arno Hao
Tel: +8618717894416